printer-20230423_142258.cfg

[include mainsail.cfg]
[include config/steppers_xy.cfg]
[include config/steppers_z.cfg]
[include config/extruder.cfg]
[include config/z_calibration.cfg]
[include config/led.cfg]
[include config/beacon.cfg]
[include config/fans.cfg]
[include config/bed_heat_home.cfg]
[include config/temp_sensors.cfg]
[include config/macros.cfg]
#[include config/input_shaper.cfg]

[mcu] # Runs XY and a chamber thermistor
serial: /dev/serial/by-id/usb-Klipper_stm32h743xx_250039000751303231393036-if00

[mcu zed] #Runs z and extruder/hotend
serial: /dev/serial/by-id/usb-Klipper_stm32h743xx_480038000751303231393036-if00

[mcu expander] #Runs bed, bed fans, and thermistors
serial: /dev/serial/by-id/usb-Klipper_stm32f042x6_030007000C43303054313620-if00

[printer]
kinematics: corexy
max_velocity: 800  
max_accel: 10000
max_z_velocity: 30
max_z_accel: 1000
square_corner_velocity: 8.0
## For Input Shaping
#max_velocity: 5000
#max_accel: 20000
#max_accel_to_decel: 20000

[input_shaper]
shaper_freq_x: 60.8
shaper_type_x: ei
shaper_freq_y: 50.6
shaper_type_y: mzv

[exclude_object]

[display_status]

[virtual_sdcard]
path: ~/printer_data/gcodes

[pause_resume]

[force_move]
enable_force_move: False

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [beacon model default]
#*# model_coef = 1.903766283120462,
#*# 	2.1673112830940915,
#*# 	0.569411636241769,
#*# 	0.1371319653126855,
#*# 	0.23317495315960465,
#*# 	0.24052105424959822,
#*# 	-0.28349146826734223,
#*# 	-0.27773359773074224,
#*# 	0.17692941056588435,
#*# 	0.13563979396135178
#*# model_domain = 3.173138782820188e-07,3.292770283085309e-07
#*# model_range = 0.200000,5.000000
#*# model_temp = 55.896392
#*# model_offset = 0.00000
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 	  0.118291, -0.001235, 0.000000, 0.172865
#*# 	  0.079790, -0.052456, -0.044772, 0.151387
#*# 	  0.045218, -0.108122, -0.097699, 0.125302
#*# 	  0.134342, -0.033800, -0.035846, 0.201058
#*# x_count = 4
#*# y_count = 4
#*# mesh_x_pps = 2
#*# mesh_y_pps = 3
#*# algo = bicubic
#*# tension = 0.2
#*# min_x = 35.0
#*# max_x = 280.0
#*# min_y = 35.0
#*# max_y = 260.0