diff --git a/UDLs/Klipper-GCODE-Dark-by-Iron3eagle.xml b/UDLs/Klipper-GCODE-Dark-by-Iron3eagle.xml new file mode 100644 index 0000000..3c41e65 --- /dev/null +++ b/UDLs/Klipper-GCODE-Dark-by-Iron3eagle.xml @@ -0,0 +1,64 @@ + + + + + + + + 00; 01 02 03 04 + + + + + + + + + + G21 + + M84 + + + + "END START GCODE" + + "END GCODE" + G0 G1 G2 G3 G4 G28 G90 G91 M18 M73 M84 M104 M105 M106 M107 M109 M112 M114 M115 M117 M118 M140 M190 M204 M220 M221 M400 + ACCELEROMETER_MEASURE ACCELEROMETER_QUERY ACCELEROMETER_DEBUG_READ ACCELEROMETER_DEBUG_WRITE ANGLE_CALIBRATE ANGLE_DEBUG_READ ANGLE_DEBUG_WRITE AXIS_TWIST_COMPENSATION_CALIBRATE BED_MESH_CALIBRATE BED_MESH_OUTPUT BED_MESH_MAP BED_MESH_CLEAR BED_MESH_PROFILE BED_MESH_OFFSET BED_SCREWS_ADJUST BED_TILT_CALIBRATE BLTOUCH_DEBUG BLTOUCH_STORE SAVE_CONFIG UPDATE_DELAYED_GCODE DELTA_CALIBRATE DELTA_ANALYZE SET_DISPLAY_GROUP SET_DISPLAY_TEXT SET_DUAL_CARRIAGE SAVE_DUAL_CARRIAGE_STATE RESTORE_DUAL_CARRIAGE_STATE ENDSTOP_PHASE_CALIBRATE EXCLUDE_OBJECT EXCLUDE_OBJECT_DEFINE EXCLUDE_OBJECT_START EXCLUDE_OBJECT_END ACTIVATE_EXTRUDER SET_PRESSURE_ADVANCE SET_EXTRUDER_ROTATION_DISTANCE SYNC_EXTRUDER_MOTION SET_FAN_SPEED QUERY_FILAMENT_SENSOR QUERY_FILAMENT_SENSOR SET_RETRACTION GET_RETRACTION ENABLE_FORCE_MOVE FORCE_MOVE STEPPER_BUZZ SET_KINEMATIC_POSITION FIRMWARE_RESTART SET_GCODE_VARIABLE GET_POSITION SET_GCODE_OFFSET QUERY_FILAMENT_WIDTH RESET_FILAMENT_WIDTH_SENSOR DISABLE_FILAMENT_WIDTH_SENSOR ENABLE_FILAMENT_WIDTH_SENSOR QUERY_RAW_FILAMENT_WIDTH ENABLE_FILAMENT_WIDTH_LOG DISABLE_FILAMENT_WIDTH_LOG TURN_OFF_HEATERS TEMPERATURE_WAIT SET_HEATER_TEMPERATURE SET_IDLE_TIMEOUT SET_INPUT_SHAPER MANUAL_PROBE Z_ENDSTOP_CALIBRATE Z_OFFSET_APPLY_ENDSTOP MANUAL_STEPPER SET_DIGIPOT SET_LED SET_LED_TEMPLATE SET_PIN PALETTE_CONNECT PALETTE_DISCONNECT PALETTE_CLEAR PALETTE_CUT PALETTE_SMART_LOAD PID_CALIBRATE CLEAR_PAUSE PAUSE RESUME CANCEL_PRINT SET_PRINT_STATS_INFO PROBE QUERY_PROBE PROBE_ACCURACY PROBE_CALIBRATE Z_OFFSET_APPLY_PROBE PROBE_EDDY_CURRENT_CALIBRATE LDC_CALIBRATE_DRIVE_CURRENT SET_PIN QUERY_ADC QUERY_ENDSTOPS MEASURE_AXES_NOISE TEST_RESONANCES SHAPER_CALIBRATE RESPOND SAVE_VARIABLE SCREWS_TILT_CALCULATE SDCARD_LOOP_BEGIN SDCARD_LOOP_END SDCARD_LOOP_DESIST SET_SERVO SET_SKEW GET_CURRENT_SKEW CALC_MEASURED_SKEW SKEW_PROFILE SET_SMART_EFFECTOR RESET_SMART_EFFECTOR SET_STEPPER_ENABLE SET_TEMPERATURE_FAN_TARGET DUMP_TMC INIT_TMC SET_TMC_CURRENT SET_TMC_FIELD SET_VELOCITY_LIMIT TUNING_TOWER SDCARD_PRINT_FILE SDCARD_RESET_FILE SET_Z_THERMAL_ADJUST Z_TILT_ADJUST TEMPERATURE_PROBE_CALIBRATE TEMPERATURE_PROBE_NEXT TEMPERATURE_PROBE_COMPLETE ABORT TEMPERATURE_PROBE_ENABLE + X Y Z + F E + I J P S T + + + + 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 + + + + + + + + + + + + + + + + + + + + + + + + + + + + + diff --git a/udl-list.json b/udl-list.json index e438c17..dd476d7 100644 --- a/udl-list.json +++ b/udl-list.json @@ -1346,6 +1346,14 @@ "description": "kiXtart", "author": "(anonymous)" }, + { + "id-name": "Klipper-GCODE-Dark-by-Iron3eagle", + "display-name": "Klipper GCODE Dark", + "version": "v1.0.0", + "repository": "https://github.com/Iron3eagle/Klipper-GCODE-Dark", + "description": "Klipper GCODE Dark", + "author": "Iron3eagle" + }, { "id-name": "LDIF_by-gambazinho", "display-name": "LDIF",