Error when patching

[EdiTnss]

I installed the mibstd2 toolbox succesfully but when i tried to patch it (/tools/patch.tsd.mibstd2 system swap and generate EL ) it gives me this error bellow.I would appreciate if you could help me.Thanks

[Medmimoza]

Did you patch with sdcard (toolbox inside)?

[Medmimoza]

What's your actual firmware version

[Medmimoza]

Ive just seen that your gem is old, ( read again how to install.
Copy cpu folder from toolbox folder and replace the one on root

[EdiTnss]

Its 0245

[Medmimoza]

Quote''
Unzip MIBSTD2-Toolbox-vX.X.X.zip to the root of SD card.
IMPORTANT! If your firmware is version 01xx or 02xx having GEM (Green Engineering Menu) version 3.x, you must use special edition of Toolbox to update it. To do this, replace cpu folder in the root of the SD card with cpu folder from \toolbox\gem folder.
Unquote " its copy past from how to install, you don't read that's all

[EdiTnss]

Ok thank you so much! I will try this

[gourtz]

hello i have same problem i install toolbox but on patching i have same thing with this. if i take reboot and try to patch again i see blak screen when i try to patch . it need to copy cpu file? if yes now how to install again same like first install or inside from toolbox.

check the photos

[Medmimoza]

You missed main step, you have GEM 3.xx
Need to replace cpu folder from root by the one from
Toolbox/ gem/..
Then install again ;-)

[gourtz]

it need to make sd again and update same like first time or it need to go inside toolbox and update from sd?

[Medmimoza]

Like first time, but replace cpu folder

[gourtz]

thank you very mutch i try it.

from 245v to update 478 480 it is safe?

[Medmimoza]

If you don't know what to do better to avoid.

[gourtz]

hello i try it again and it works. and patch applied. but i have an error b201a

[Medmimoza]

Try to put clean firmware 254T into a good sdcard, then click on retry

[gourtz]

from my mistake i delete my previous post i make new toolbox with cpu replaced and open the navigation and installed again and it works...
not work ok but i have a fault b201a in vcds

[Medmimoza]

Erhis error is normal, when you use update fonction even with official software this error appears
Go to 5F / adaptation/ confirmation of installation change/ then copy 4 digicode,
Copy on generator
http://mib-helper.com/im-so-xory/
Generate, you will get 4 digicode
Repalace old vale then save, clean eroor/ then should be fine
Everything is in this vidéo
https://youtu.be/0tpPm-ucAwc

[Medmimoza]

So when you plug usb data, android auto button became bigger, just click on it and fellow steps

[gourtz]

Thank you so mutch...

[gourtz]

I try it with vcds and fix it with xory but now i have new fault

[gourtz]

This is ok?

[gourtz]

Also my mirror link doesnt work i try it different settings in my phone xiaomi 11 t pro and in mib2 app connect and mirrorlink and android auto settings. Do you have a guide or something else?

[Medmimoza]

No need to add fec, just patch swap/ generate EL, Using toolbox

[gourtz]

is ok patched

[gourtz]

i restart and i try it with car scanner it has fault and i try with vcds and says out of range

[Medmimoza]

Good so FEC are enabled even if you didn't see them on fec installed list, when you clic on app button you should see " android auto, carplay, mirror link" mean everything is well patched and add

[gourtz]

i check tomorrow and i sent you. thank you for your support.

[leonfrpt]

Hi,

I do have a Seat Leon 5F from 2019 with this firmware installed MST2_EU_ZR_P0514T (0514) installed. i do know that there is an update to version 516. My car comes with navi system and a 2 slot sd card, already with voice request ativated.

My question is, can i patch this unit to release Full Link option just by runing MIB-std2-pq-zr-toolbox option "Patch tsd.mibstd2.system.swap and generate EL"?

Thanks to you all for your support.

[leonfrpt]

Sorry, correct firmware MST2_EU__SE_ZR_P0514T (0514)